ReBuilder® Technical Specifications
Model 300
Model 600
Model 2407
ReBuilder Model 300
Electrically isolated output. This is a safety feature so that if an accidental short occurs due to dropping etc. within the unit, it cannot reach the patient.
Pulse duration: 240 microseconds positive / 1.458 microseconds negative
Pulse waveform: Asymmetrical, biphasic, with very short positive spike for nerve stimulation and negative, broad peak of longer duration for muscle stimulation. This is a patent pending feature. This waveform exactly duplicates the waveform of a healthy nerve signal much the same as a pacemaker imitates a healthy cardiac signal.
Pulse repetition rate: 7.8 Hz
Peak charge per pulse: 7.23 microColumbs @ 500 ohm load
Pulse amplitude: 0 to 40 volts @ 500 ohm load, continuously variable
Peak pulse current: 0 to 80 mA @ 500 ohms
Power source: 9 V alkaline battery (supplied)
Intended mode of action:
The 7.8 Hz setting is designed to control pain by stimulating the large afferent nerves. By utilizing the conductive garments, the entire skin area of the foot is treated which distributes the signal and ensures a suitable comfort level. Also available are conductive gloves for the hands.
There are other DC components in the signal that re-set the set points of the nerves, and when used with the conductive garments, induces a nerve signal by the nerves themselves that adds to the effectiveness.
Certain proprietary aspects of the output signal are withheld and it is these aspects that are primarily responsible for the success of the ReBuilder.
Note: It is extremely dangerous to use a common TENS or EMS device to treat neuropathy as it can overload the nerves causing permanent damage. The ReBuilder is processor controlled and has real-time biofeedback functions built in that read the patient's electrical parameters and makes constant adjustments to match the patient's immediate nerve function.
Weight: 6 oz. (with battery)
Dimensions: 2 3/8" x 3 3/4" x 1"
Made in the USA.
Fully registered with the FDA
Back to Top of Page
ReBuilder Model 600
Electrically isolated output. This is a safety feature so that if an accidental short occurs due to dropping etc. within the unit, it cannot reach the patient.
Pulse duration: 240 microseconds positive / 1.458 microseconds negative
Pulse waveform: Asymmetrical, biphasic square pulse, with very short positive spike for nerve stimulation and negative, broad peak of longer duration for muscle stimulation. This is a patent pending feature. This waveform exactly duplicates the waveform of a healthy nerve signal much the same as a pacemaker imitates a healthy cardiac signal.
Pulse repetition rate: 7.8 Hz
Peak charge per pulse: 20 microColumbs @ 500 ohm load
Pulse amplitude: 0 to 40 volts @ 500 ohm load, continuously variable
Peak pulse current: 0 to 80 mA @ 500 ohms
Power source: 9 V alkaline battery (supplied)
Intended mode of action:
The 7.8 Hz setting is designed to control pain by stimulating the large afferent nerves. By utilizing the conductive garments, the entire skin area of the foot is treated which distributes the signal and ensures a suitable comfort level. Also available are conductive gloves for the hands.
There are other DC components in the signal that re-set the set points of the nerves, and when used with the conductive garments, induces a nerve signal by the nerves themselves that adds to the effectiveness.
Certain proprietary aspects of the output signal are withheld and it is these aspects that are primarily responsible for the success of the ReBuilder.
Note: It is extremely dangerous to use a common TENS or EMS device to treat neuropathy as it can overload the nerves causing permanent damage. The ReBuilder is processor controlled and has real-time biofeedback functions built in that read the patient's electrical parameters and makes constant adjustments to match the patient's immediate nerve function.
Weight: 6.5 oz. (with battery)
Dimensions: 2 1/2" x 3 3/4" x 1.25"
Made in the USA.
Fully registered with the FDA
Back to Top of Page
ReBuilder Model 2407
Electrically isolated output. This is a safety feature so that if an accidental short occurs due to dropping etc. within the unit, it cannot reach the patient.
Pulse duration: 240 microseconds positive / 1.458 microseconds negative
Pulse waveform: Asymmetrical, biphasic, with very short positive spike for nerve stimulation and negative, broad peak of longer duration for muscle stimulation. This is a patent pending feature. This waveform exactly duplicates the waveform of a healthy nerve signal much the same as a pacemaker imitates a healthy cardiac signal.
Pulse repetition rate: Switch-Selectable: 7.83 Hz, 90 Hz (TENS), and 90 Hz (EMS) modulated 6 seconds on and 6 seconds off with 0.25 second ramp-up and 0.25 second ramp-down within the 6 seconds while on.
Peak charge per pulse: 7.23 microColumbs @ 500 ohm load
Pulse amplitude: 0 to 40 volts @ 500 ohm load, continuously variable
Peak pulse current: 0 to 80 mA @ 500 ohms
Power source: 9 V alkaline battery (supplied)
Intended mode of action:
The 7.8 Hz setting is designed to control pain by stimulating the large afferent nerves. By utilizing the conductive garments, the entire skin area of the foot is treated which distributes the signal and ensures a suitable comfort level. Also available are conductive gloves for the hands.
There are other DC components in the signal that re-set the set points of the nerves, and when used with the conductive garments, induces a nerve signal by the nerves themselves that adds to the effectiveness.
Certain proprietary aspects of the output signal are withheld and it is these aspects that are primarily responsible for the success of the ReBuilder.
Note: It is extremely dangerous to use a common TENS or EMS device to treat neuropathy as it can overload the nerves causing permanent damage. The ReBuilder is processor controlled and has real-time biofeedback functions built in that read the patient's electrical parameters and makes constant adjustments to match the patient's immediate nerve function.
Weight: 8 oz. (with battery)
Dimensions: 3" x 1.5" x 6.25"
Additional Settings: EMS and TENS
Made in the USA.
Fully registered with the FDA
Back to Top of Page